Phoenix & the Valley · Water damage helpMon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Home › FAQ

Water Damage Questions, Answered

Every question answered on this site, in one place — what to do first, how drying works, what insurance covers, and how to spot a slab leak.

FAQ

All questions

Shut off the main water supply if it is safe to do so, move valuables and electronics off the floor, and stay away from wet outlets and switches. Take photos of the water and every room it reached, then call for help. Do not wade through water near electrical fixtures.

It depends on how much water there is and how many rooms it reached. A single wet room can be extracted in one visit; a whole floor takes longer, and drying continues after extraction. Moisture readings, not the clock, decide when the work is done.

Sometimes. It depends on the water source, how long the carpet stayed wet, and the condition of the pad underneath. Clean water from a supply line is different from sewage water, which is treated as contaminated. Moisture readings and the pad condition decide what can stay.

Drywall wicks water upward from the floor line, and baseboards trap moisture behind them. A wall can be wet a foot up from the floor while the room looks dry. A moisture meter finds that; eyes alone do not.

Sudden, accidental water damage from inside the home is often covered by a standard homeowners policy, while flooding from outside usually needs a separate flood policy. Check your policy, keep your photos and readings, and talk to your insurer about the claim.

Drying starts: air movers and dehumidifiers are placed on the mapped wet areas, readings are recorded, and the materials are checked again until they read dry. Cleaning and any repair work follow once the structure is dry.

It depends on how long the boards stayed wet and how much water they absorbed at the edges. Boards that cup or lift after a soaking often do not flatten again once they dry, because the wood has swollen unevenly. A moisture meter reading of the boards and the slab underneath tells you whether drying in place is still sensible or whether the flooring has to come up.

Usually not, for a small wet area. Drying equipment is noisy and the rooms it sits in are out of use while it runs, but the rest of the home stays usable. If the water was sewage, or if drying equipment fills the main living areas, staying elsewhere for a few nights is worth considering. The crew can tell you on the first visit what the footprint of the job will be.

Water follows the slab. In a Phoenix home the floor is a flat concrete slab, so water runs across it under walls and baseboards into the next room, and it wicks up drywall as it goes. A leak in the kitchen can wet the living room carpet without any water ever falling there. That is why the moisture map covers rooms beyond the one with the visible water.

It depends on how much water there was, what it touched, and how long it sat. Extraction can happen in one visit; drying usually takes days, with readings checked along the way. A small wet room finishes sooner than a whole floor. The moisture readings decide the timeline, not a fixed number of days.

Extraction is one step — removing the standing water. Restoration is the full job: extraction, moisture mapping, drying, cleaning, removal of material that cannot be dried, and a final moisture check. Extraction without drying leaves wet walls and floors behind.

Sometimes, if the drywall is saturated or the cavity behind it is wet and cannot dry from the surface. Small sections are opened so air can reach the wet area and readings can be taken inside the wall. Drywall that reads dry is left alone.

Sudden, accidental water damage from inside the home is often covered by a standard homeowners policy. Flooding from outside the home usually needs a separate flood policy, and gradual leaks are often excluded. Check your policy and keep photos and readings for the claim.

It depends on how much of the home is wet, whether the water was contaminated, and whether drying equipment is running in living spaces. Your situation is assessed on the call and at the first visit — safety and the water source decide.

Moisture readings. The wet areas are checked at the start and again at the end, and the work is complete when the readings show the materials are dry. Ask for the readings — they are the record that the drying worked.

Category 2 is grey water under the IICRC S500 standard — water with significant contamination, such as washing machine or dishwasher discharge. It can cause discomfort or illness on contact, so the cleanup is stricter than for clean water: carpet pad that absorbed it is usually removed, surfaces are cleaned more thoroughly, and protective gear is worn throughout. The source of the water, not its colour, decides the category.

Mitigation is the first half: getting the water out, drying the structure, cleaning, and removing material that cannot be dried. Rebuilding is the second half: putting the room back together with new drywall, flooring, paint and trim. Mitigation takes days and ends on moisture readings; rebuilding takes weeks and starts only after the structure is dry.

Yes. Clean water left standing warms up and picks up contamination from the floors, walls and debris it sits on, and after a day or two it is treated as a higher category. That is why the time between the leak and the first visit matters, and why a leak found days later is a bigger job than the same leak found the same day.

Usually not by a standard homeowners policy. Flood — water that enters from outside, from the ground up — is generally excluded and needs a separate flood policy through the National Flood Insurance Program or a private insurer. Check your policy and talk to your insurer; keep photos and readings from the cleanup.

A burst pipe is water from inside the home, released suddenly — often covered by a standard policy. Flood damage is water from outside the home, such as monsoon rain or surface runoff — usually excluded from a standard policy. The source of the water decides how the claim is treated.

Small amounts of clean water can be mopped up, but flood water from outside carries dirt and debris, and the wet area is usually bigger than it looks. Hidden water in walls and under flooring needs meters to find. If the water is deep, contaminated, or near electrical fixtures, call for help.

Extraction happens in one visit in most cases; drying takes days, with readings checked along the way. The size of the wet area and how long the water sat decide the timeline. Readings, not the calendar, say when it is dry.

Move what you can off wet floors to a dry area, and take photos before you move anything. Rugs and soft furnishings that soaked up flood water may need cleaning or removal depending on the water and how long they stayed wet.

Start with the entry point found during cleanup — a door threshold, a window well, a drain, a roof leak. Clearing drains and gutters, checking door seals, and keeping water away from the foundation are the usual first steps. A roofer or drainage contractor handles the fix itself.

Yes, treat it as contaminated. Flood water that entered from outside is classed as Category 3 under the IICRC S500 standard, because it carries soil, debris and whatever it picked up on the way in. Keep children and pets away, wear boots and gloves if you must go near it, and wash with soap and hot water after any contact. Porous materials it soaked are removed rather than cleaned.

A wash is a normally dry channel that carries water only when it rains. Phoenix has many of them, and during a monsoon burst a wash can fill in minutes. Homes near a wash, and streets that cross one, are the first to see water. If your home took water from a wash, the entry route is noted during cleanup so the next storm can be prepared for.

No. The National Weather Service warns that six inches of moving water can knock a person down and two feet can move a car, and flood water hides the road underneath. Turn around and find another route, or wait where you are. A car that stalls in flood water is a rescue, not a shortcut.

Sudden, accidental water damage from a burst pipe is often covered by a standard homeowners policy, provided the home was maintained and heated normally. Check your policy, keep photos and readings, and talk to your insurer about the claim.

Shut off the main water supply if it is safe to do so, move valuables off wet floors, and stay away from wet outlets and light fixtures. Take photos of the water and the damage, then call for help.

Most Phoenix homes have the shutoff at the meter box near the street or on the house wall near the water heater. Turn the handle until it stops. If you cannot find it, call — and check the location now, before the next emergency.

Yes, if damp materials stay wet. The EPA notes mold can begin to grow on damp surfaces within 24 to 48 hours, which is why extraction and drying start early and why readings are checked until materials are dry.

It depends on how wet the ceiling cavity and insulation are. Small sections are opened when the cavity cannot dry from the surface or when saturated insulation must come out. Drywall that reads dry is left alone.

It depends on how much water was released and what it soaked — ceiling, insulation, walls, flooring. Drying usually takes days, with readings checked along the way. The readings decide when it is done.

Two different trades. A plumber repairs or replaces the failed pipe or fitting — that job ends when the water stops and the line holds pressure. A restoration crew handles everything the water touched: extraction, moisture mapping, drying, cleaning and removal of material that cannot be dried. The rebuild — drywall, paint, flooring — is a third step that starts only after the structure reads dry.

Heat and age, not cold. Attic supply lines sit in heat that reaches 150 degrees and more in July, and fittings and flexible supply hoses age in that heat year after year. Rubber hoses harden and split, seals dry out, and joints loosen. High water pressure adds stress at every bend. A freeze is the least likely cause of a burst pipe in the Valley.

Yes, if they are old rubber hoses. Rubber hardens with age and heat, and a split hose can release a large volume of water while nobody is home. Braided steel lines last longer. Check the hoses where they meet the wall and the machine — bulging, cracking or rust at the fitting means the hose is at the end of its life.

Look for a warm patch on a hard floor, damp flooring, the sound of running water when taps are off, a rising water bill, or a drop in pressure. The meter test helps: stop all water use, including irrigation, and see whether the meter still moves. If it moves, a leak is likely and a detection specialist should locate it.

It depends on your policy. Sudden, accidental water damage is often covered; slow leaks and the pipe repair itself are often treated differently. Check your policy and talk to your insurer — and keep photos and readings from the water damage work.

A plumber or leak-detection specialist locates and repairs the line under the slab. The water damage work — mapping, drying, and dealing with wet flooring and walls — is separate, and it can start while the repair is being arranged if rooms are already wet.

Yes, if materials stay damp. The EPA notes mold can begin to grow on damp surfaces within 24 to 48 hours, and a slab leak can keep materials damp for weeks before it is found. That is why drying and a mold check are part of the work.

It depends on the flooring and how wet it is. Carpet can often be lifted at the edge to check and dry the pad; tile and wood are checked for loosening and cupping. Flooring that cannot dry back to a sound condition is removed rather than left in place.

Longer than a burst pipe, because the water has usually been there for days or weeks and has soaked deeper — including into the slab. Readings are taken over days until the materials and the slab read dry.

Turn off every tap, toilet, appliance and hose in the house, then look at the water meter. If the dial keeps moving with everything off, water is leaving the system somewhere it should not — which points to a leak in a hidden line, often under the slab. The test confirms a leak exists; acoustic listening and thermal imaging are what locate it.

Three local factors work together. The soil is caliche and expansive clay, which swells when wet and shrinks when dry, stressing buried pipes at joints. Phoenix water is hard — 14 to 22 grains per gallon — and pits the inside of copper lines over decades. And many homes built between 1960 and 1990 have copper supply lines run under the slab, which puts those lines at the end of their life now.

It depends on the condition of the line. A single pinhole in an otherwise sound line suits a spot repair: open the slab above the leak and replace that section. A line that has leaked before, or copper that is pitted along its length, suits a reroute — abandon the old line and run a new one through the attic or walls. A reroute costs more in pipe and labour but leaves the slab untouched and puts the line where it can be reached.

Usually not on a standard policy — sewer and drain backup often needs a separate endorsement. Check your policy for a water backup endorsement and talk to your insurer. Keep photos and readings from the cleanup for the claim.

Keep people and pets away from the water, do not flush or run taps, and do not use the washing machine. Stay out of rooms where water is near electrical outlets. Then call for help — sewage water is contaminated and is not a household cleanup job.

No — sewage water is contaminated, and household tools spread it rather than removing it safely. Porous materials that touched it usually need removal, and the rooms need proper cleaning and drying. Call for help.

Carpet pad that soaked up sewage water is usually removed, because contamination soaks into it. Carpet itself is assessed by condition and how much water it took. Hard flooring is cleaned rather than removed in most cases.

Common causes are a blockage in the main line, a damaged line to the street, or a monsoon burst that overwhelmed a drain. A plumber or drain specialist looks at the line itself; the cleanup crew deals with the water and the rooms.

It depends on how much water there was and what it soaked. Drying usually takes days, with readings checked along the way. The rooms are checked again for smell and moisture before the work is considered done.

Category 3 is the most contaminated class of water under the IICRC S500 standard — grossly contaminated water that can carry bacteria, viruses and parasites. Sewage backup, toilet overflow with solid waste, and flood water that entered from outside all fall in this class. Porous materials that touch it are removed rather than cleaned, and protective gear is worn throughout the cleanup.

A backwater valve sits on the main sewer line where it leaves the house. It lets water flow out and closes when water tries to flow back in, which protects the home when the street sewer surcharges during a storm. It is installed by a plumber on the main line and needs checking from time to time so it still moves freely.

That points to the main line, not one fixture. When a single drain is slow, the blockage is usually in that fixture's own pipe. When several drains slow together, or a toilet gurgles when another fixture runs, the blockage is in the main sewer line that serves the whole house — tree roots, grease build-up, or a surcharge from the street sewer.

It depends on how much water there was, what it soaked, and how long it sat. A small wet area can dry in days; a whole floor or a slab-leak area takes longer. Moisture readings are checked during drying, and the readings — not the calendar — say when it is dry.

Household fans move air, but they do not dehumidify, and they cannot reach water inside walls, under flooring, or in a slab. Structural drying pairs air movement with dehumidification and verifies the result with meters. A room that feels dry without readings may still be wet inside.

Desert air dries surfaces fast, but drywall, insulation and concrete hold moisture inside. The surface evaporates first; the inside takes longer. A moisture meter reads the inside — that is the number that matters.

A dehumidifier helps by pulling moisture from the air, but on its own it does not push air across a wet floor or into a wall cavity. Drying pairs dehumidifiers with air movers, placed on a mapped wet area.

Moisture readings. The wet areas are read at the start and again during drying, and the work is complete when the readings show the materials are dry. Ask for the readings — they are the record that drying worked.

They may stay damp inside for weeks, especially insulation, slab and wall cavities. The EPA notes mold can begin to grow on damp surfaces within 24 to 48 hours, so slow, unverified drying is the risky option.

Under the IICRC S500 standard, a drying job is classed 1 to 4 by how much water the structure holds and how deeply it is held. Class 1 is the lightest — a small area, tile or concrete. Class 4 is the heaviest — water held deep inside dense materials such as hardwood, plaster and concrete. The class decides the equipment and the timeline, and it is set by moisture readings.

A dry standard is the moisture level the material should return to, measured with a pin moisture meter and compared against the same material in a part of the home the water never reached. That unaffected-room reading is the target. Drying is finished when the wet areas match the dry reference — not when the surface feels dry to the touch.

Desert heat dries the face of drywall fast, while the cavity behind it stays damp. A hand on the surface reads the face; a pin meter reads inside the material. The inside is what matters, because moisture trapped in a wall cavity is where mold starts. The equipment stays until the inside reading matches the dry reference.

According to the U.S. EPA, mold can begin to grow on damp surfaces within 24 to 48 hours. That is why extraction and drying start early after a leak or a flood — the first two days matter most.

This site does not make health claims. The EPA's guidance is that damp indoor spaces should be dried and cleaned, and mold can begin to grow on damp surfaces within 24 to 48 hours. If you have health concerns, talk to a doctor.

No — it depends on how long materials stayed damp. A leak that is found and dried quickly may not lead to growth; a slow leak that ran for weeks is far more likely to. Drying early and verifying with readings is the way to reduce the risk.

Both. Hard surfaces can often be cleaned. Porous materials that stayed wet — drywall, insulation, carpet pad — often cannot be cleaned properly and are removed instead. Readings and condition decide, case by case.

It depends on your policy and on the cause of the water damage. Sudden, accidental water damage is often covered; gradual leaks and mold on its own are often treated differently. Check your policy and talk to your insurer.

Fix the water source first, dry the materials to verified readings, and remove material that cannot be dried or cleaned. If the source is not fixed, the damp returns — and so does the growth.

The EPA says that if the moldy area is less than about 10 square feet — roughly a 3 foot by 3 foot patch — in most cases you can handle the job yourself, following its cleanup tips: fix the water problem, scrub hard surfaces with detergent and water, dry everything completely, and wear gloves, goggles and an N-95 respirator. Larger areas, heavy water damage, or sewage water point to professional remediation.

Because the moisture problem was not fixed. The EPA states that mold will return if the growth is cleaned but the water problem is not corrected. A cleaned wall with a leak still running behind it, or a wall that was never dried to its dry standard, will grow mold again. Fix the source, dry the structure to verified readings, then clean — in that order.

No — not until it is checked. The EPA says that if you suspect the heating or cooling system may be contaminated with mold, you should not run it, because it can spread mold through the house. Have the system checked first, and keep it off until the check is done.

Shut off the main water supply if it is safe to do so, move valuables off wet floors, and stay away from wet outlets and light fixtures. Take photos of the water and the damage, then call for help.

Sudden, accidental water damage from a burst pipe is often covered by a standard homeowners policy, provided the home was maintained and heated normally. Check your policy and keep photos and readings for the claim.

Most Phoenix homes have the shutoff at the meter box near the street or on the house wall near the water heater. Turn the handle until it stops.

It depends on how wet the ceiling cavity and insulation are. Small sections are opened when the cavity cannot dry from the surface or when saturated insulation must come out. Drywall that reads dry is left alone.

Yes, if damp materials stay wet. The EPA notes mold can begin to grow on damp surfaces within 24 to 48 hours, which is why extraction and drying start early and readings are checked until materials are dry.

The washing machine hoses, because there are two of them, they carry full supply pressure around the clock, and they sit behind the machine where nobody looks at them. Check them where they meet the wall and the machine — bulging, cracking or rust at the fitting means the hose is at the end of its life.

They fail differently. An attic pipe sends water straight onto the ceiling below, so it shows fast and spreads across the room. A wall pipe soaks the drywall and framing quietly, and the first sign is a stain or a soft spot days later. Both need the same response: shut off the main supply, then map the wet area with a moisture meter.

It depends on how much water is coming in. Water dripping from a ceiling light fixture, a sagging ceiling, or water spreading across a floor needs attention now. A small stain that appeared after a storm still needs checking — the attic above it may be wet even if the room looks fine.

Sudden damage from a storm is often covered by a standard homeowners policy, but gradual wear and a roof that was not maintained are often treated differently. Flood water from outside usually needs a separate flood policy. Check your policy and talk to your insurer.

The water damage inside the home can be dealt with during rain; the roof repair itself is usually done once the rain stops and the roof is safe to work on. A roofer handles the repair.

Water travels along the roof deck, down rafters and across insulation before it drips through the ceiling. The stain shows where the water came out, not where it got in — which is why the attic has to be checked.

It depends on how wet the ceiling and the insulation above it are. Small sections are opened when the cavity cannot dry from the surface or when saturated insulation must come out. Drywall that reads dry is left alone.

Because water travels along the underlayment and the roof deck before it finds a way through the ceiling. A leak that starts over one room can show up as a stain in the next room, or in the middle of a ceiling far from the failed tile. Finding the entry point takes a roofer on the roof, not a guess from inside the house.

They leak differently. A pitched roof sheds water; a flat roof ponds it, and the water leaves through scuppers and drains. A scupper clogged with leaves and dust is the most common reason a flat roof ponds until the water finds a seam. Clearing the scuppers and drains before monsoon season is the most useful hour of prep for a flat roof.

It is urgent, though not a fire-level emergency. Water landing on drywall under an attic air handler gets worse the longer the system keeps running. Turn the thermostat off, mop up what you can reach, and get the drain looked at within a day or two.

Most Phoenix AC water leaks are drainage failures, not refrigerant leaks: a blocked condensate drain, an overflowing or corroded pan, or a frozen coil melting down. Hard water mineral buildup is the usual cause of the blockage.

A homeowner can often clear a clog with a wet/dry vacuum at the outdoor termination of the drain line. Cutting lines or bailing an attic pan is not homeowner work — and the water damage to the ceiling still needs checking.

Sudden, accidental water damage from an AC system is often covered by a standard homeowners policy; gradual leaks and wear are often treated differently. Check your policy and keep photos and readings for the claim.

A moisture meter reads the drywall and the insulation above it. A stain can be old and dry, or it can mark a ceiling that is still wet inside. The reading decides — eyes alone cannot tell.

Because the insulation above the ceiling soaked the water up first. The insulation holds water until it is saturated, then lets it through to the drywall below. By the time the stain shows, the insulation is wet and the drywall is wet from above — which is why the insulation is checked along with the ceiling itself.

Both, in order. An HVAC technician fixes the drain: clears the clogged line and checks the pan and the float switch. A restoration crew dries the ceiling: checks the moisture in the drywall and insulation and places drying equipment. The drain is fixed first — there is no point drying a ceiling while the pan is still filling.

Sudden, accidental water damage from an appliance — a hose that bursts, a tank that fails — is often covered by a standard homeowners policy. A slow seep that went unnoticed for months is often treated differently. Check your policy and keep photos for the claim.

Shut off the supply valves behind the machine, mop up what you can reach, and move laundry and rugs off the wet floor. Do not run the machine again until the hose is replaced. Call for help with the wet rooms.

Yes — water pools under the unit and soaks the subfloor and the cabinet bases beside it, often before any water appears on the kitchen floor. Moisture meters check under and beside the unit.

Look for water pooling around the base of the tank, rust or damp on the floor in the garage or closet, and a musty smell near the unit. A tank that has failed can release a large volume at once.

It depends on how wet the cabinet bases are and whether they can dry to a verified reading. Swollen bases that cannot dry are removed; bases that read dry are left in place.

Watch for rust-coloured water from a hot tap, a rumbling or popping sound when the heater runs, water pooling at the base of the tank, or dampness on the floor around it. A drain pan under the heater, with a drain line to the outside, catches a slow leak before it becomes a flood.

Yes — the steel braid protects the rubber core inside, so they last longer. But the rubber inside still ages, and the fitting where the hose meets the wall is still the weak point. Check every supply hose where it meets the wall and the appliance, whatever it is made of — bulging, cracking or rust at the fitting means the hose is at the end of its life.

Keep people and pets away from the water, do not flush or run taps, and do not use the washing machine. Stay out of rooms where water is near electrical outlets. Then call for help.

No — sewage water is contaminated, and household tools spread it rather than removing it safely. Porous materials that touched it usually need removal, and the rooms need proper cleaning and drying.

Usually not on a standard policy — sewer and drain backup often needs a separate endorsement. Check your policy for a water backup endorsement and talk to your insurer.

Common causes are a blockage in the main line, a damaged line to the street, or a monsoon burst that overwhelmed a drain. A plumber or drain specialist looks at the line itself.

Carpet pad that soaked up sewage water is usually removed, because contamination soaks into it. Carpet itself is assessed by condition and how much water it took.

Because the blockage is in your own line, not the street. Tree roots, grease build-up, or a collapsed section can block the main sewer line at any time, with no rain involved. A backup that happens during heavy rain points at the street sewer surcharging; a backup on a dry day points at your own line.

It shows the inside of the line: roots growing through joints, cracks, collapsed sections, grease build-up, and where the line narrows. The inspection decides whether the fix is a cleaning or a new section of line — and it is the record that proves what caused the backup.

The National Weather Service defines Arizona's monsoon season as June 15 to September 30. The most active part is usually mid-July to mid-August, when storm frequency and rainfall peak.

Usually not by a standard homeowners policy. Flood — water that enters from outside, from the ground up — is generally excluded and needs a separate flood policy through the National Flood Insurance Program or a private insurer. Check your policy.

A haboob is a massive wall of dust driven by a thunderstorm's outflow winds. The July 2011 haboob over Phoenix was nearly 5,000 feet tall and about 100 miles wide. Maricopa County reports one to three dust storms in an average year.

Start with the entry point found during cleanup — a door threshold, a window well, a drain, a roof leak. Clearing drains, checking door seals, and keeping water away from the foundation are the usual first steps. A roofer or drainage contractor handles the fix itself.

Small amounts can be mopped up, but flood water from outside carries dirt and debris, and the wet area is usually bigger than it looks. Hidden water in walls and under flooring needs meters to find. If the water is deep or near electrical fixtures, call for help.

A wash is a normally dry channel that carries water only when it rains. During a monsoon burst it can fill in minutes, because the water comes from the whole area that drains into it — a storm miles upstream can send water down a wash that has not seen a drop of rain. Homes near a wash, and streets that cross one, are the first to see water.

It is an Arizona law that allows drivers who are rescued from flooded washes to be billed for the rescue. It exists because people keep driving into flooded washes, and the water is stronger than it looks — six inches of moving water can knock a person down and two feet can move a car. The rule is simple: turn around, do not drive through it.

Water damage in your Phoenix home?

Call Now to reach a local water damage professional. Describe the water, where it is, and what it has touched.

Call Now

Contact

Call now for water damage help

Tap Call Now to reach a local water damage professional. Tell them where the water is, what it has touched, and whether it is still coming in.

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

Call Now

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the water and the damage for your records.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the water started and what caused it, if you know.
Phoenix Water Damage Pros — helper
☎ Call Now